Precision-turbo-and-engine BigStuff3 GEN3 PRO SEFI (LS1) System Hardware & Manual de usuario Pagina 64
- Pagina / 122
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
BigStuff3 Pro SEFI System (LS1)
Version 1.0 63
The illustration below shows the areas of the base fuel map that the ECU accesses under
different driving conditions.
Hint: Use the 02% Correction feedback in the Dash to help calibrate the Fuel table VE values.
Note: Be sure the ECU is properly configured and the Base Fuel and Spark Tables
are calibrated before configuring and calibrating any of the following engine
operating parameters.
34. STARTING
The “Starting” drop-down selections allow the user to calibrate parameters associated with
starting (cranking) and running the engine for a short period of time (temperature dependent)
after the engine is initially started.
To configure engine starting fuel, go to Starting on the Tool Bar. Left click on “Starting” and a
drop down screen will open. Keep the left mouse button depressed and slide the mouse pointer
down until the desired “Starting” fuel drop down is highlighted.
The BigComm software allows the user to configure the Load (MAP)
and RPM axes allowing for a larger number of cells (map area) to be
used for the fuel and spark tables.
- BigComm Software 1
- User Instruction Manual 1
- Table of Contents 2
- Table of Contents Continued 3
- 1. Introduction 3
- 3. Package Contents 6
- Firewall grommet 7
- LS1 In-line, 1-by-4, IAC 14
- Connector Pin-out 14
- IAC Coils 14
- Late Model 2-by-2 IAC 14
- Pin-Out 15
- WBO2 & 16
- Coil V-Batt 16
- 30 Amp fuse 16
- WBO2 & Coil V-Batt Relay 16
- 7. ECU Installation 19
- 8. BigComm Software Overview 19
- BigComm software CD ROM 20
- BigComm 24
- 11. Using the Tool Bar 25
- BigComm desktop icon 26
- 13. BigComm Main Menu Screen 30
- 15. Closing Windows 30
- 16. Configuration 31
- 17. Hardware Configuration 31
- For setup detail go to 33
- Coil-on-Plug (COP) 33
- Crank_Reference_Setup 33
- TPS Signal in the Dash 34
- 19. Dwell Time Table 38
- 20. Load vs. RPM 40
- 21. Firing Order 44
- 22. Injector Opening Time 44
- 23. Injector Phase Angle 45
- 25. Air Fuel Ratio Table 48
- 26. Positive 02 Correction 52
- 27. Negative 02 Correction 53
- 30. SPARK (F4 – “Quick Key”) 56
- 31. Spark Table 57
- 32. FUEL (F3 – “Quick Key”) 60
- 33. Fuel Table 61
- 34. STARTING 64
- 36. After Start Delay 66
- 37. After Start Correction 67
- 38. After Start Decay 68
- 39. Idle 69
- 40. Throttle Follower 70
- 41. Desired Idle RPM 71
- 42. Idle Spark 71
- 43. IAC Start Position 72
- 44. IAC Gain Terms 73
- 45. Warm Up 74
- 48. TRANSIENT FUEL 76
- 51. MAP AE Decay Rate 79
- 52. MAP AE Inc Rate 80
- 53. Run Time Correction 81
- 54. dMAP Parameters 82
- 55. dTPSdt 84
- 56. AE Position Correction 85
- 57. Individual Cylinder 86
- 60. Boost 88
- 61. Boost Parameters 89
- 62. Boost PWM 90
- 63. Boost Staged 91
- 65. Learning 94
- 67. Learning Display Table 95
- 68. Dash 96
- 69. Configure Dash 96
- 70. Save a Dash 99
- 71. Load From File 101
- 72. Save to File 102
- 73. Logging (External) 104
- 74. Configure Log 105
- 76. View Log from File 106
- Red cursor 109
- 79. Configure Replay 111
- 80. Upload 112
- 81. View Replay From File 113
- Blue Ellipse represents the 116
- 85. Load Calibration 118
- To set up, go to Gear_Box 120
- To set up, go to Gears 120
- 87. Acronym Definition 121
- 88. Control Keys 121
- 89. Function or “Quick Keys” 121
- 90. Definitions 121
- 91. ECU Pin-out 122
Relacionado con productos y manuales para Para El Coche Precision-turbo-and-engine BigStuff3 GEN3 PRO SEFI (LS1) System Hardware &
Para El Coche Precision-turbo-and-engine NLR AMS-1000 Boost Controller Manual de usuario
(25 paginas)
(25 paginas)
Para El Coche Precision-turbo-and-engine Precision Turbo & Engine PW46 Wastegate Manual de usuario
(9 paginas)
(9 paginas)
Para El Coche Precision-turbo-and-engine Precision Turbo & Engine PW66 Wastegate Manual de usuario
(9 paginas)
(9 paginas)
Para El Coche Precision-turbo-and-engine Precision Turbo & Engine PW39 Wastegate Manual de usuario
(9 paginas)
(9 paginas)
Para El Coche Precision-turbo-and-engine BigStuff3 GEN3 Powertrain Controller Ignition Setu Manual de usuario
(34 paginas)
(34 paginas)
Para El Coche Precision-turbo-and-engine BigStuff3 GEN3 1st Gear Spark Retard with Traction Manual de usuario
(21 paginas)
(21 paginas)
Para El Coche Precision-turbo-and-engine BigStuff3 E85 Sensor Wiring Diagram Manual de usuario
(1 paginas)
(1 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.029 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales